Genie Introduces New S™-60 and S™-65 Trax Telescopic Booms

New booms designed with innovative four-point track system.

NEWARK, UK. (September 17, 2008) – Genie unveils the latest addition to its telescopic boom family — S™-60 and S™-65 Trax models. The new Trax booms feature an innovative four-point track system that allows contractors to work any time of the year, enhancing traction for travel in many types of difficult terrain. This introduction expands Genie’s telescopic boom product offering to include the new Trax models as well as an aftermarket tracks option for wheeled units.

The new S™-60 and S™-65 Trax models from Genie are manufactured with a four-point track system permanently “fixed”, or attached, on the machine. Genie’s fixed-track booms are designed with a narrower profile — 2.59 m wide — to allow these booms to be easily transported. The Trax models are designed with an inside turning radius of 3.35 m and an outside turning radius of 6.40 m, and because the Genie® Trax booms steer like a wheeled unit, operators can easily drive these machines on and off the delivery trailer, as well as manoeuvre in close proximity to walls and foundations. The Trax booms have a travel speed of 2.7 mph.

“Track booms are ideal for working year-round by enhancing traction for travel in muddy, soft-soil, sandy, snowy and wet ground conditions,” says Phil Harvey, product manager, Genie Industries. “And, they can also easily travel over harder surfaces like gravel, rock, concrete and asphalt, and sensitive turf. A four-point track system offers the increased traction and flotation as two-track units with excellent terrain tracking, machine handling and operator comfort. Our track booms can drive through many places previously inaccessible even with rough-terrain tyres.”

Each track in the four-point system is made of durable, steel-reinforced rubber and measures 43 cm wide and 101 cm long, with each carriage assembly weighing 500 kg. With a ground contact pressure of 9.2 psi for the S™-60 and the 9.7 psi for the S™-65, the four-point track system leaves a minimal impression on sensitive surfaces. During travel, each track flexes 23° up and down to accommodate the contour of the landscape, for a smooth ride during operation and travel. The four-point track system works in conjunction with Genie’s active oscillation axle system, which senses the terrain and adjusts the axle position based on ground conditions, and positive traction drive system, which maintains equal power to all tracks even if one track loses traction. Combined, these features give Genie® track booms the ability to smoothly travel over difficult terrain conditions.

To maximise usage of its wheeled models, Genie continues to approve Loegering’s Quad Track System (QTS) as an aftermarket option for the S™-60 and S™-65 telescopic booms, as well as the Z™-60/34 articulating model. This “flexible”, or interchangeable, track system is a set of four track undercarriages that fastens directly onto a boom’s standard wheel hubs in place of the tyres. With this option, Genie customers have the flexibility to simply bolt on the tracks when needed and switch back to the traditional wheeled machine configuration when tracks are not needed. The entire system can be put on or taken off the booms in less than four hours. The addition of this option increases the machine width to 2.70 m, which may require special oversized load transport permits.

Both the S™-60 fixed and flexible track models offer 227 kg lift capacity at the maximum horizontal outreach of 15.48 m up to a working height of 20.34 m The S™-65 models provide a 227 kg lift capacity at the maximum horizontal outreach of 17.1 m to a working height of 21.86 m.

The Genie® fixed and flexible track booms are designed for increased uptime. The undercarriages are constructed out of high-grade steel and feature fully sealed greaseless bearings for minimum maintenance. The four-point track system also features an easy-grease tensioning system for fast, reliable track adjustment. And, to limit the amount of debris buildup during operation, V-shaped; self-cleaning pads are incorporated into the track design.

Contact Information
Emily Lowth
Tel +44 (0)1476 584382
Email emily.lowth@genieind.com

About Genie
Headquartered in Redmond, Wash., with branch offices worldwide, Genie Industries manufactures material lifts, aerial work platforms, trailer-mounted booms and light towers, scissor lifts, self-propelled telescopic and articulating booms and telehandlers. For more information, please visit www.genieindustries.com.

Genie Industries, Inc. is a subsidiary of TEREX Corporation (NYSE: TEX), a diversified global manufacturer based in Westport, Conn. For more information on TEREX, please visit www.terex.com.